Archives

How to Refurbish An Old Dining Chair?

How to Refurbish An Old Dining Chair
Adding fresh fabric or a brand new cushion to an old dining chair can be excellent way to breathe life into it. However, the task can seem overwhelming and extensive if the correct method is not followed. One must also be careful about choosing the right upholstery fabric and materials for completing the work. Given below is the step-by-step procedure for refurbishing a dated dining chair:

  • First the seat base must be unscrewed from the frame, after which the staples and fabric will have to be removed using pliers and an awl. For newbie DIY enthusiasts, it is important to exercise great care while pulling the staples off.
  • In order to replace the worn out seat, a new one will have to be created from a plywood measuring ½ inch. The outline of the base can either be traced on the plywood piece or marked with proper dimensions. It is better to use a jigsaw for cutting around the markings.
  • The next requirement is a seat cushion which will have to extracted from a piece of 1 inch-dense foam. Once the cushion is ready, it must be attached to the wood using a spray adhesive that dries quickly. The edges should be rounded by spraying them with glue and then sticking them to base of the seat.
  • Now the foam must be covered with a layer of polyester batting that is ½ inch dense. First the batting can be stapled to the centre of all sides of the base and pulled around for covering the foam entirely.
  • The calculated dimensions of the seat base must be increased by ¼ inch and then used as measurements for cutting the fabric. In case a pattern is being used, it has to be centred on the chair first.
  • The fabric should be made as tight as possible and then attached to the base using staple gun in the same way as the batting.
  • In case the dining chair needs protection from dust, a cover must be prepared from black cambric fabric, which can be stapled to the underside. Finally, the seat can be screwed back to the frame.

Although the above mentioned steps are not very difficult to execute, they do necessitate a certain amount of skill. In case an individual finds them hard to take care of, he or she must get in touch with a reputed firm performing furniture repair & reupholstery in Sydney and allow professionals to complete the job.

How to Choose Fabrics For Upholstering Old Furniture?

How to Choose Fabrics For Upholstering Old Furniture
Image Source: johnlewis.com

It is not uncommon to find old furniture at a Sydneysider home. Sometimes, it may so happen that a piece is still in good condition with an overall good framework. However, its upholstery seems to be anything but usable anymore. If such is the case, then the most prudent thing would be to hire a efficient professional dealing with furniture upholstery in Sydney. But before that, there is another thing that must be taken care of. And that is picking a suitable fabric type for upholstering the furniture piece.

Comparing fabrics can seem like a cumbersome task to any newbie. But following a few simple steps can help in choosing the most appropriate one:

Taking The Style & Colour Into Account

It is important to assess the style and colour of furniture upholstery fabrics while trying to pick a good one from among them. The option being considered must match with the furniture that needs to be upholstered. For instance, a modern and large couch placed in the centre of the living room has to be dark enough for hiding stains, wear and tear from regular usage, etc.

Considering The Durability

The fabric being chosen must be tough enough for withstanding the strains of regular usage. If it is a couch, for example, the material used for upholstering it must be something heavy and thick such as wool or leather. A wingback chair, on the other hand, will require something soft like rayon or silk.

Examining The Thread Count

While buying fabrics for furniture upholstery, one of the most vital aspects that must be checked is the thread count. The best way to do that is by reviewing the description or label of the material being considered for purchase in order to determine the number of threads used in every square inch. Something with a high thread count is more likely to last longer.

Checking The Grade

Upholstery fabrics are generally graded with alphabets (F being the highest grade and A, lowest). The grades generally determine the cost of different fabrics, the lower one being cheaper.

Deciding Whether The Requirement Is Sunlight or Stain Protection

There exist many fabric types which are designed or treated specifically for withstanding sunlight and spills. One must decide what they want to protect their furniture upholstery from.

At the time of buying upholstery fabrics, it is important to look for a card that would contain all necessary information. If a card or tag is absent, one must ask for it from the vendor.

Furniture Requirements of Modern Restaurants

Furniture Requirements of Modern RestaurantsFurniture have a paramount role to play in enhancing the ambiance of any space, be it a home, business place or restaurant. But the kind of furniture that must be bought depends on the purpose for which it would be used. In this blog, we will talk about the furnishings required for equipping a restaurant.

To begin with, most of us know that restaurants are prone to food and drink spills. Therefore, the fabrics used for upholstering restaurant furniture must be capable of resisting stains and repelling water. At the same time, they should also be good enough for providing comfortable seatings to visitors. This kind of fabric can be easily procured from any reputed firm dealing with commercial upholstery in Sydney.

Next comes the elementary furniture styles and items required for furnishing a restaurant. Let’s have a look at some of the primary ones:

Booth

A booth within an eatery is simply an area having a table and high backed chairs that act like partitions. Nowadays, booths have become very common in most restaurants of Sydney due to their unique and professional look. They can generally be seen in 2 different types –

  • The first type features 2 sides, with a dinner table between them and a seating bench on each side.
  • The second type features one side with chairs and the other side jutting out from the wall. A table is placed in between.

Chairs

They are among the most commonly used furniture items in eateries. Chairs in restaurants perform a two-fold duty – they provide convenient seatings to guests and also serve as decorative components. They come in a wide range of designs and materials. Some places even use stools instead of chairs for imparting a unique look, such as coffee shops.

Dining Tables

Dining tables meant for use in restaurants are available in different sizes and shapes. The variants also differ in terms of price and constituent material. Their aesthetic appeal is generally accentuated with the help of various accessories like tablecloths and centrepieces.

Pub Tables

Being elegant and tall, pub tables are often used as an alternative for their dining counterparts in many eateries throughout Sydney. These tables allow visitors to be at the same height as their accomplices while they are seated.

Besides the above mentioned options, some eateries also use lounge furniture for upping the levels of comfort and elegance, which have a unique ability to transform the areas where they are kept into relaxation zones.

Measuring a Chair Before Buying Upholstery Material For It

Measuring a Chair Before Buying Upholstery
Re-covering an upholstered chair is quite an ideal way for revitalising its look as well as bringing colour to the overall decor of the room. Before doing so, however, it is important to measure the chair properly and purchase the correct volume of upholstery materials needed as per the measurements. Knowing the quantity of materials required would also help in comparing prices of the available options and getting the best deal.

Given below is the correct process of measuring a chair properly:

At first, the seat cushion must be removed from the chair, in case that is possible. After that, the thickness or height and length of the cushion will have to be measured properly with the help of a measuring tape. Both the measurements should be multiplied by two and then added together.

Now, each of the chair arms will have to be measured by starting from the outer part where the fabric covering exists, right up to the end portion of the arm fabric along the inner part of the seat. The width of the arms can be determined by measuring along their widest point. Now both of the end results will have to multiplied by two and added together.

The height of the chair must be measured along its back from the topmost part to the lowest portion where upholstery exists. It is also important to determine how tall the back support cushion is. Once that has been done, the depth of the seat will have to be measured accurately from its back to the chair’s front. If the cushion is not removable, the depth should be determined across the cushion.

Ultimately, the height of the upholstered chair along its front, starting right from where it meets the fabric or cushion and ending at the lowest point of the upholstered surface, must be measured.

Finally, all the measurements that have been taken during the entire process must be added to get a total amount. This amount must then be divided by 1000 in order to convert the entire measurement to metres.

Now a fabric of the obtained length can be bought from any reputed firm dealing with upholstery in Sydney. The product selected must be in a colour, style and pattern that suits the decor of the room where the chair is kept. The length of the fabric must be rounded to the next 1 metre to allow for any error that might have been made.

Mattresses and Bedheads for King-Sized Beds

Mattresses and Bedheads for King-Sized Beds
King-sized beds are generally suitable for large spaces and provide a lot of area for two people to sleep in and stretch out for getting a good night’s rest. The headboard for these beds come in a wide range of styles, sizes and materials. Most people buy them in order to match the existing decor and furnishings. Let’s have a look at two of the main components of king-sized beds:

Mattress

Mattresses designed specifically for king-sized beds are generally 203 centimetres long and 193 centimetres wide. To be exact, they are 41 centimetres wider than queen-sized mattresses. They are probably the widest of their kind available in the market and are approximately of the same size as a couple of twin beds kept together. A king mattress usually requires either 2 large pillows or 3 standard ones.

Headboard

There are many people who prefer custom made bedheads for their king-sized beds instead of readymade ones. As a result, there is no standard size set for them. However, the headboard must be at least 193 centimetres wide for accommodating the mattress. In general, the width of typical king bedheads ranges from 201 to 213 centimetres. They are manufactured in a wide range of styles, with the width quite often depending solely upon the style.

As has been mentioned already, headboards for king-sized beds usually come in a plethora of styles, sizes and materials. Iron, wood and leather are the most commonly used manufacturing materials. Some of the bedheads are designed with inbuilt shelves to be functional, while others have an upholstered finish. Typically sleek and modern lower headboards might be only 109 centimetres tall, whereas mid-size leather variants generally range from 125 to 137 centimetres. For instance, sleigh style bedhead made out of wood is often as tall as 152 centimetres. In other words, there is no standard height for the bedheads, but it usually lies between 109 and 177 centimetres.

While selecting headboard for a king sized bed, the foremost thing that must be taken into account is the current decor. The product bought should match its style and colour. It is also important to consider the space available within the room. Analysing the height and width of the bed is essential as well. Mattresses often range from 20 to 46 centimetres in thickness. Height of the bedhead must coordinate with that of the bed frame as well as the mattress.

Refinishing An Antique Furniture Piece

Refinishing An Antique Furniture Piece
Antique furniture pieces are basically items that have aesthetic or sentimental value for their owners. It is therefore important to exercise suitable measures for preserving them properly, refinishing being one of them. Given below is the procedure for refinishing an antique furniture piece.

Prior to beginning with the refinishing job, it is essential to confirm that the furniture does not have a pre-existing layer of patina. One must also carefully read as well as comprehend the instructions given on all the solvents and chemicals that have been chosen for executing the task.

The next vital step is to decide whether the antique needs a thorough cleaning or its old finish has to be stripped off. Sometimes, cleaning can help in understanding what actually requires to be done. While in other cases, a coat of varnish can be enough to bring back the original luster.

When using a paint remover, most experts of antique furniture restoration in Sydney recommend applying a thick layer in one stroke. It would form a pudding-like skin on the surface, and placing a newspaper or plastic on it can help to keep the remover from drying out. It is important to ensure that the surface being worked on has been kept in a horizontal position. The paint stripper should not be removed until a finger can be rubbed down into bare wood.

Once the stripper has done its work done properly, it has to be scraped off using a putty knife or an obsolete credit card. Putty knife can cause damage to the wood if handled inappropriately, therefore it is more prudent to utilise an old credit card.

After that, the piece must be washed down either with water or a suitable solvent. Reading the container of the solvent is essential, in order to determine whether the product about to be used is appropriate or not. Scrubbing with help of a stiff brush having coarse wood chips can be ideal.

For removing light scratches, one can rub the surface of antique piece with a fine grit sandpaper. To sand different mouldings and shapes on the item, old felt may be used as well.

To stain the antique furniture, using pigmented wiping stain would be the best bet. It is not only colour fast, but can also be utilised for highlighting and developing grain of various wood species. The stain should be brushed on, allowed to stand for a minute and then wiped dry. After that, the finish can be put on using a piece of soft cloth and allowed to dry for 24 hours. Three or four coats of the finish might just be enough for completing the refinishing work.

How to renovate your home office in easy steps

How to renovate your home office in easy steps
Are you running a business from your home? Do you own a home office? In case you do then you might often have to work some extra shifts (when you are not attending your business calls) reflecting on how to wrestle with the precise and unavoidable renovation costs while doing a facelift with the office space at home. You would be reassured to know that you are not alone in this. There are scores of micro entrepreneurs having the same issue with their workspace. Many home based entrepreneurs would like to make their workspace more functional and better looking at tight budget. If this happens to be your wish too then all you need to do is read below.

Customizing wood framed layouts

The design of your home office space should be tantalizing indeed if you happen to encompass specific strategies for the wood framed layouts which are there in your house. You can choose to morph your regular mirror into a wood framed one. You can get interior walls installed (with wooden frames) in case you have got a big room. This way you will be able to segregate your work space from the rest of the room and make room for more privacy and solitude which will be conducive to your work.

Furniture restoration with commercial upholstery solutions

Furniture restoration and remodeling initiatives form a highly central part in the entire periphery of commercial upholstery services. It is really going to work great in terms of offering a quick fix to your existing furniture and revamping them entirely for a much better show. Resorting to the opportune helpline catered by companies offering commercial upholstery in Sydney is a workable option that might be considered in this connection.

Flooring

Floors happen to be an integral part of your room and you can definitely do something with the floor of your office space at home. It would be helpful for you to make arrangement of carpets. You can purchase a good looking carpet and cover up the entire floor. In a way, it is highly economical as there will be plenty of inexpensive carpets available in the market. If you do not feel a thing for carpet then you can linoleum tiles or check board floors a priority for you. Hardwood flooring and laminate flooring will also do as they are durable and affordable.

Painting

You can get the walls and floors of your room painted in order to add a new curb appeal. Painting will definitely be a great initiative in terms of sprucing up the room at a nominal cost. The best part is that it is a mess free process for you.